momeight05

How to Replace a Kia Sportage Replacement Key For a number of Kia models, the key contains the keyless entry system that is built into the key. The key can be compared to the remote control and can be changed with a new one from a Kia dealer or locksmith. Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons signals, signal interference, water damage, and a defective receiver module. Here are some guidelines on how you can get your Kia Sportage replacement key to work again. How to replace a smartkey or remote key? The battery in your Kia's intelligent key will eventually need be replaced, regardless of whether it's a remote key or a push-to-start one, or a standard metal key that doesn't have a transponder. This is especially in the event that your vehicle displays a message that indicates that the remote or smart key is not powered by the battery. It's a simple process. In order to replace the battery on the key fob take out the mechanical key from the slit at the back of the key fob and remove the cover. Inside the key fob will be tiny screws that hold the battery in place. Using a small screwdriver, unscrew the screw and remove the old battery. Insert the new battery and then close the gap on the key fob. When the key fob is equipped with an updated battery Test it by pressing the lock and unlock buttons. You're in good shape if the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to run errands around Brandon. Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll have to note the key code's number on the key code tag. How do you replace a dead battery? If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A weak battery could cause other issues, like the check engine light flashing or the engine not cranking properly. It is quite simple to replace key fob batteries using just a few simple tools. Make sure you turn off your vehicle and shut all doors before you begin. Locate the small plastic piece at the bottom of your key fob and play with it until a metallic key slides out. G28 Car Keys Solutions can then insert the key into the handle on the door of your driver to unlock your car. To replace the key fob battery, remove the cover on the rear and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then place the new battery so that its “+” side is facing you and the “–”, negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts. Once the new battery is installed after which you turn the key fob off and then turn it on in the ignition until the door locks. You can then test the Kia's Key fob to ensure it's functioning properly. How to replace a smart key You could have the standard keyfob or Smart Key, based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade while the standard key fob does not. Both types of key fobs have batteries inside that eventually will need to be replaced. This is a simple procedure that takes only two minutes. Be sure to turn off your Kia, and be on a flat or well-lit surface prior to when you begin. Keep in mind that there are tiny parts inside the fob that could be snagged if not careful. The release button for the small size is located on the lower backside. It's either an oval or circular slot. Once you press this mechanical key blade, it will appear and you can then open the key fob. Once the key fob is opened, take out the battery that was in it. The new battery is a CR-2032, and can be purchased online or in your local auto parts store. Once you're done, your key fob should be able to lock and unlock your vehicle, even if it isn't running. How to replace the mechanical key The Kia keyfob can be a fantastic convenience, allowing us to lock or unlock our car by pressing the button. Like any device it is possible that the Kia key fob might have issues. There are steps to take to fix these issues and ensure that our key fobs are in good condition over the long haul. One of the most common problems is a dead or dead battery. This can cause the device to stop working entirely or stop working at times. If this is the problem, replace the battery with an entirely new battery. If this doesn't fix the problem Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be sure not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one. Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working properly. If the device isn't working, call an authorized locksmith or dealer to solve the problem. Make sure they cut you an emergency key that functions across all trunk and door cylinders to prevent lockouts in the future.